How to Sync Renpho Scale to Garmin Connect

Prerequisites

Before we start, make sure you have:

• A Renpho smart scale (any model with Bluetooth or WiFi)
• iPhone running iOS 16.0 or later
• Renpho Health app installed and connected to your scale
• Garmin Connect account
• Apple Health app (pre-installed on iOS)
• Stable WiFi or Bluetooth connection

Step 1: Set up Renpho with Apple Health

Initial Renpho Scale Setup

1. Download the Renpho Health app from the App Store
2. Create an account or log in to your existing Renpho account
3. Follow the in-app setup to pair your Renpho scale:
   • Turn on your scale and ensure it's in pairing mode
   • Select your scale model in the app
   • Complete the Bluetooth/WiFi pairing process
4. Test the connection by stepping on your scale and verifying the data appears in the Renpho Health app

Connect Renpho to Apple Health

1. Open the Renpho Health app
2. Tap on your profile/settings (usually a profile icon)
3. Look for "Apple Health" or "Health Sync" options
4. Tap "Connect to Apple Health" or similar option
5. In the Apple Health permissions screen:
   • Toggle "Weight" to ON (required)
   • Optionally enable other metrics like Body Fat %, BMI, etc.
   • Tap "Allow"

Step 2: Download and Configure WeightSyncr

Install WeightSyncr

1. Download WeightSyncr from the App Store
2. Open the app - you'll immediately see a Health permissions request
3. Tap "Continue" to proceed to Apple Health permissions
4. In the Apple Health screen:
   • Ensure "Weight" is toggled ON
   • Tap "Allow" to grant permissions

Verify Data Access

1. After granting permissions, WeightSyncr should automatically show your recent weight entries
2. You should see entries with timestamps matching your Renpho scale measurements
3. If no data appears, try pulling down to refresh or check the Apple Health permissions again

Step 3: Connect to Garmin Connect

1. In WeightSyncr, tap the "Settings" tab at the bottom
2. Tap "Connect Garmin Account"
3. Enter your Garmin Connect credentials:
   • Email address associated with your Garmin Connect account
   • Your Garmin Connect password
4. Complete 2FA if enabled:
   • If you have two-factor authentication enabled, enter the code when prompted
   • WeightSyncr fully supports Garmin's 2FA system
5. Tap "Authorize" to complete the connection
6. Verify connection: You should see "Connected" status in the Settings tab

Step 4: Test the Sync

Manual Test

1. Step on your Renpho scale to get a fresh weight measurement
2. Wait a few seconds for the data to sync to the Renpho Health app
3. Open WeightSyncr and pull down to refresh the Home tab
4. Find your new weight entry and tap the sync button (⚡) next to it
5. Check Garmin Connect:
   • Open the Garmin Connect app or website
   • Navigate to Health Stats → Weight
   • Your new measurement should appear within a few seconds

Set Up Automatic Sync (Premium)

For automatic syncing without opening the app:

1. Consider upgrading to WeightSyncr Premium
2. Premium enables automatic background syncing
3. Your weight data will sync to Garmin Connect immediately after stepping on your Renpho scale
4. Check our pricing options for current Premium features

Troubleshooting

Renpho Data Not Appearing in WeightSyncr

• Check Apple Health connection: Verify Renpho data appears in Apple Health app
• Verify WeightSyncr permissions: Settings → Privacy & Security → Health → WeightSyncr
• Force refresh: Pull down on WeightSyncr Home tab
• Restart both apps: Force close Renpho Health and WeightSyncr, then reopen

Renpho Scale Not Syncing to Apple Health

• Check Renpho app permissions: Open Renpho Health → Settings → Apple Health integration
• Re-enable data sharing: Turn off Apple Health integration in Renpho app, then turn it back on
• Update the Renpho Health app to the latest version
• Ensure scale connectivity: Check that your scale is properly connected via Bluetooth or WiFi
• Reset scale connection: Remove and re-add your scale in the Renpho Health app

Garmin Connection Issues

• Verify Garmin credentials: Try logging into garmin.com directly
• Reconnect account: In WeightSyncr Settings, disconnect and reconnect your Garmin account
• Check for Garmin service issues: Visit connect.garmin.com
• 2FA issues: See our comprehensive 2FA troubleshooting guide

Advanced Features

Body Composition Data

Many Renpho scales measure more than just weight:

• Body Fat Percentage
• Muscle Mass
• BMI (Body Mass Index)
• Water Percentage
• Bone Mass

Currently, WeightSyncr focuses on weight data synchronization. However, all this additional data is preserved in Apple Health and available for other apps to use.

Multiple User Support

If multiple people use the same Renpho scale:

• Each person needs their own iPhone with separate Apple ID
• Each person installs WeightSyncr individually
• Each person connects to their own Garmin Connect account
• The Renpho scale can distinguish between users and send data to the correct phone

Historical Data Import

To import historical weight data from your Renpho scale:

1. Ensure all historical data is in Apple Health (check the Renpho Health app sync settings)
2. Use WeightSyncr's "Sync Past Entries" feature (Premium)
3. Select your desired date range
4. WeightSyncr will bulk upload your historical data to Garmin Connect

For detailed instructions, see our bulk sync guide.

Frequently Asked Questions

Does this work with all Renpho scale models?

Yes! This setup works with any Renpho smart scale that can sync to Apple Health, including all WiFi and Bluetooth models. The key requirement is that your scale must be compatible with the Renpho Health app.

Will my body composition data sync to Garmin?

WeightSyncr currently focuses on weight data synchronization. While your Renpho scale may measure body fat, muscle mass, and other metrics, these are stored in Apple Health but not automatically synced to Garmin Connect through WeightSyncr.

How quickly does the data sync?

With manual sync: Immediate after tapping the sync button. With Premium automatic sync: Within seconds of your weight appearing in Apple Health. The entire chain (Scale → Renpho App → Apple Health → WeightSyncr → Garmin) typically takes less than 30 seconds.

Can I sync historical data?

Yes! WeightSyncr Premium includes bulk sync functionality that can upload months or years of historical weight data from Apple Health to Garmin Connect in one operation.

What if my Renpho scale stops working?

WeightSyncr works with any data in Apple Health, regardless of the source. You could switch to a different smart scale brand, manually enter weight data, or even use a regular scale with manual entry - as long as the data reaches Apple Health, WeightSyncr can sync it to Garmin.

Does this drain my iPhone battery?

No. WeightSyncr is designed to be very battery-efficient. The automatic sync feature uses minimal background processing and only activates when new weight data appears in Apple Health.